Skip to content

WaytoICT

通往ICT之路 · 光通信与AI网络技术解读

中文English
登录注册
Menu
Technology Optical comms · silicon photonics · CPO → Market Insights Financials · trends · industry → In-Depth Analysis Optical chips, devices & modules → Video Understand a topic in minutes → Documents Latest docs · summit materials →
Menu

How Much Can Optical Fiber Be Bent?

Posted on 2023-08-18 by

Overview of Optical Fiber Bending

Optical fiber sensors are small and bendable, and can be installed in samples in confined spaces. However, an excessively small bending radius brings optical signal loss, affecting the accuracy of sensing measurements. In many practical application scenarios, the installation of optical fiber sensors inevitably involves small bending radii, so how to solve the loss caused by fiber bending has become a focus of attention.

Let’s look together at what harm ordinary fiber bending brings and the working principle of the small bending radius of bend-insensitive fiber.

Why Optical Fiber Cannot Be Excessively Bent

When light travels from one medium into another, refraction and reflection occur at the interface of the two media. As the incident angle increases, the reflected light becomes stronger and the refracted light becomes weaker; when the incident angle is large enough, the refracted light completely disappears, leaving only reflected light. This phenomenon is called total internal reflection.

How Much Can Optical Fiber Be Bent?

Figure 1 Total internal reflection phenomenon. Optical fiber consists of a three-layer structure of core, cladding, and coating. The core refractive index is greater than the cladding refractive index, so light can achieve total internal reflection transmission in the core. Refer to Optical Fiber Communication Basics.

How Much Can Optical Fiber Be Bent?

Figure 2 Total internal reflection in optical fiber. The loss coefficient of a general standard single-mode fiber at 1550 nm is about 0.2 dB/km, with very low transmission loss. If the fiber is bent (macrobend or microbend), the optical transmission no longer satisfies the total internal reflection condition, and part of the light leaks from the cladding, causing optical power loss.

How Much Can Optical Fiber Be Bent?

Figure 3 Fiber bending state

How to Reduce Bending Loss

The main cause of loss in an optical fiber link is large-angle bending at local positions of the fiber during installation and laying, commonly at fiber joints and fiber turns. This type of bending loss is reversible; increasing the bending radius of the fiber will greatly improve link loss. What Is the Transmission Path of Light in an Optical Fiber.

Using OFDR equipment to measure the fiber link, an OFDR distribution curve (distance-intensity/reflectance) can be obtained. The curve can reflect the loss at each position in the fiber link, with loss mainly presented in the form of steps, as shown in Figure 4. Users can use the OFDR curve to analyze and find the bending position and make adjustments.

How Much Can Optical Fiber Be Bent?

Figure 4 OFDR curve when fiber is bent. In addition, users can choose bend-insensitive (bend-resistant) fiber as sensors to reduce the impact of bending loss. Bend-resistant fiber can tolerate smaller bending radii; for example, single-mode high-temperature-resistant strain fiber (model: PI125) has a minimum bending radius of about 5 mm, and tight-buffered strain sensing cable (model: SS-0.9mm) has a minimum bending radius of about 8 mm.

Introduction to Bend-Resistant Fiber

Conventional single-mode fiber (G.652 type) recommends a bending radius greater than 5 mm (diameter 1 cm), otherwise the optical signal will have significant loss, causing the signal-to-noise ratio of sensing measurements to decrease and measurement results to become unstable. Regarding the minimum bending radius, the rule of thumb is: for long-term applications, the bending radius should exceed 150 times the fiber cladding diameter; for short-term applications, it should exceed 100 times the cladding diameter. The conventional single-mode fiber cladding diameter is 125 μm, so the above two minimum bending radii are 19 mm and 13 mm respectively. Optical Fiber Communication: What Are Mode Field Diameter and Cutoff Wavelength?

Bend-resistant fiber (G.657 type) mainly improves bend resistance by changing the fiber structure design. There is a relatively universal indicator for evaluating bending sensitivity in the industry: the MAC value.

How Much Can Optical Fiber Be Bent?

The MAC value is the ratio of the mode field diameter to the cutoff wavelength in a near-step-index waveguide fiber. As the MAC value decreases, the fiber’s sensitivity to bending decreases. Some basic methods for designing bend-insensitive fiber, simply put, are to reduce the mode field diameter, or increase the cutoff wavelength, or both, to make bend-insensitive fiber. The specific methods are:

(1) Reduce the mode field diameter to improve optical confinement, such as reducing the core diameter or increasing the core refractive index.

(2) Reduce the fiber cladding diameter to increase bend resistance. The diameter of existing bend-resistant fiber has been reduced from 125 microns to 80 microns, and even fiber with a 60-micron outer diameter has appeared.

(3) Add a ring of low-refractive-index trench to the cladding, functionally similar to increasing the core refractive index.

The above methods can all better confine the light beam in the core for transmission, thereby reducing the impact of fiber bending in sensing measurements. The commonly used bend-resistant fiber type on the market is G.657B3, and its bending radius and bending loss parameters are shown in the table below, for reference only.

How Much Can Optical Fiber Be Bent?

Related articles:

  • What Are the Characteristic Parameters of Optical Fiber?
  • The Composition of Fiber Loss and How to Reduce Fiber Loss

A large number of fiber-related documents can be obtained by joining the “Communication Encyclopedia” Knowledge Planet, where you can also download other 10000+ resources!


Related Reading

  • What Is the Transmission Path of Light in an Optical Fiber?
  • Optical Fiber Communication: The Structure of Optical Fiber
  • Optical Fiber Communication: Mode Field Diameter and Cutoff Wavelength

Enjoy this article?

Subscribe to get new optical communication insights delivered to your inbox. Free, unsubscribe anytime.

Category: Technology

Leave a Reply

You must be logged in to post a comment.

订阅更新

订阅后,新文章发布时第一时间收到邮件通知

李东霏
光互连技术研究者

香农信息技术研究院,专注光模块、CPO、硅光与 AI 光互连的技术解读。

行业报告

光芯片·光器件·光模块 2026 报告汇编(含 OFC 2026)

光芯片 · 光器件 · 光模块
2026 报告汇编(含 OFC 2026)

¥1,900

上/下两册,收录 OFC 2026 一线报告
添加微信 WaytoICT 订购

广告

📢 广告位招商:面向全球光通信客户 侧边栏广告位 Email:Dongfei.li@shannoninstitute.cn

最新文档

  • 互连拐点:11 页解析机架内到多机架 Scale-Up 的 XPO/CPX/OCI 蓝图(OCP 2026 全球峰会)
  • AI 时代的相干光技术:17 页解析 Scale-Across、液冷 XPO 与全谱转发器(OCP 2026 全球峰会)
  • XPO 高密度光互连的系统级评估:20 页解析 212G SerDes 平台与 FRO/LRO/LPO 实测(OCP 2026 全球峰会)
  • CPO 与 OCI 标准及未来技术:17 页 Broadcom 精简版演讲提纲(OCP 2026 全球峰会)
  • VCSEL 高密度互连:7 页解析 50G NRZ「慢而宽」阵列与光 PCIe 演示(OCP 2026 全球峰会)

最新评论

暂无评论,欢迎登录后发表第一条评论。

最近访客

👥 今日访客 -
加载中…
© 2026 WaytoICT | 蜀ICP备2020035321号-2 | 隐私政策 | 免责声明
Wechat Pay
Alipay
请使用 支付宝 或 微信 扫码支付