Skip to content

WaytoICT

通往ICT之路 · 光通信与AI网络技术解读

中文English
登录注册
Menu
Technology Optical comms · silicon photonics · CPO → Market Insights Financials · trends · industry → In-Depth Analysis Optical chips, devices & modules → Video Understand a topic in minutes → Documents Latest docs · summit materials →
Menu

Mitsubishi: Comparing DC Termination and AC Coupling for Dual-EAM Differential EML

Posted on 2026-10-30 by 李, 东霏

The day before yesterday I wrote about Mitsubishi’s glass-substrate dual-EAM differential EML flip-chip scheme at ECOC 2026.

Whether at OFC 2026 or ECOC 2026, its EMLs all adopt a dual-EAM series structure.

Mitsubishi dual-EAM series differential EML structure

The anode of EAM1 and the cathode of EAM2 are tied to a common ground, the two EAMs have exactly the same physical length, and an SSC spot-size converter is used to improve fiber coupling efficiency.

By connecting the two EAMs in series, the total capacitance is halved, which exactly offsets the doubling of the RC time constant caused by the 100-ohm termination resistor under differential drive.

Meanwhile, electrical isolation is provided between the DFB and the two EAMs, so the differential drive voltage is applied only to the EAM electrodes, preventing signal leakage into the laser and crosstalk between the two EAMs.

For differential RF high-speed signals, termination schemes are mainly divided into two types: DC termination and AC coupling.

Comparison of DC termination and AC coupling schemes

The core difference between the two schemes lies in how the termination matching resistor is grounded. Because the EAM requires a DC bias voltage to operate, this involves the path of the DC current.

In DC termination, the 50-ohm termination resistor is connected directly to the ground plane of the substrate, so the DC current generated by the bias flows directly through the resistor to ground.

DC termination with the 50-ohm resistor connected directly to ground

Current flowing through the resistor generates heat and consumes power, and data centers have extremely high requirements for low power consumption.

But DC termination resistors are grounded independently, so the photocurrents of the two EAMs can be drained separately, providing high tolerance to process imbalance and current mismatch, and the low-frequency common-mode response does not degrade.

At OFC 2026 in the first half of the year, Mitsubishi used chip-on-carrier (CoC) wire bonding and measured a 3-dB bandwidth exceeding 100 GHz at the limit.

OFC 2026 chip-on-carrier CoC packaging

The threshold current was 8 mA, and at a DFB-LD injection current of 100 mA, the output power reached 19 mW.

At ECOC 2026, Mitsubishi switched to sub-mount packaging. Under DC termination, 113 GBaud PAM4 testing achieved a TDECQ of 0.96 dB, and the 3-dB electro-optic bandwidth reached 80 GHz.

ECOC 2026 sub-mount packaging DC termination test

At this point the EAM bias voltage was +1.65 V / -1.65 V, the extinction ratio was 3.3 dB, and the output power was 8.8 dBm. The difference between differential and common mode was greater than 10 dB, with good low-frequency common-mode rejection.

To solve the high power consumption caused by DC bias current flowing through the resistor, Mitsubishi introduced an AC coupling scheme, i.e., a DC-blocking capacitor in series between the resistor and ground.

To save packaging area, Mitsubishi did not give each of the two 50-ohm resistors its own capacitor; instead it connected the two resistors together and shared a single 10 nF AC coupling capacitor to ground.

Single-capacitor AC coupling termination scheme

The DC-blocking capacitor blocks DC and lets only the high-frequency RF signal reach ground. This achieves RF matching while blocking DC current, greatly reducing power consumption.

Measured at 113 GBaud PAM4, the 3-dB bandwidth with AC termination remained at 80 GHz.

At this point the AC termination positive/negative bias was +1.45 V / -1.45 V, TDECQ was 0.59 dB, extinction ratio 3.5 dB, and output power 8.9 dBm.

AC termination 113 GBaud PAM4 test results

It can be considered that at 113 GBaud, the modulation performance of AC termination and DC termination is almost identical.

Mitsubishi achieved 360 Gb/s with DC termination at OFC 2026, but it consumed too much power.

Therefore, Mitsubishi ran a 155 GBaud (310 Gb/s) test based on AC termination. At 100 mA current and 1.2 Vppd swing, it achieved a TDECQ of 2.1 dB, extinction ratio of 3.7 dB, and output power of 9.0 dBm.

155 GBaud (310 Gb/s) AC termination test

Of course, the single-capacitor AC scheme also has risks. If the dual-EAM photocurrents are unbalanced and lack independent grounding, the common-mode response may degrade, whereas DC termination has no such risk.

In the article a few days ago, I also discussed Mitsubishi’s glass-substrate flip-chip scheme, which likewise uses AC coupling. Flip-chip is used to reduce the per-channel area and improve integration density.

But this sacrifices performance: the bandwidth dropped from 80 GHz with wire bonding to 60.3 GHz.

Finally, a brief summary.

Summary of DC termination and AC coupling schemes

Thanks for reading, and apologies for any inaccuracies!

Further reading:
Innolight: EML MPD-free optical power monitoring based on EAM photocurrent
Coherent: traveling-wave electrode high-speed EML scheme
Lumentum: 4x200G differential-drive EML progress

The OFC 2026 report compilation on optical chips, optical devices, and optical modules is printed in color with A4 binding, two volumes totaling 1000+ pages, about 1700 hand-drawn structure diagrams and about 200,000 words. Contact us to order at an affordable price!

You can add WeChat WaytoICT to join the Semiconductor & Optical Device Industry Group 2.

Welcome to join our community for high-value technical documents, trend reports, and supply-demand opportunities in the semiconductor chip, optical device, and optical module fields.

WaytoICT report compilation and services

If you are interested in semiconductors, optical devices, optical modules, and fiber-optic communications, welcome to follow us!


Related Reading

  • Maximum coupling loss (MCL) and maximum path loss (MPL)
  • How to couple VCSEL light into the PIC wafer plane?
  • Silicon photonics series 2: what is a grating coupler?

Enjoy this article?

Subscribe to get new optical communication insights delivered to your inbox. Free, unsubscribe anytime.

Category: Technology

Leave a Reply

You must be logged in to post a comment.

订阅更新

订阅后,新文章发布时第一时间收到邮件通知

李东霏
光互连技术研究者

香农信息技术研究院,专注光模块、CPO、硅光与 AI 光互连的技术解读。

行业报告

光芯片·光器件·光模块 2026 报告汇编(含 OFC 2026)

光芯片 · 光器件 · 光模块
2026 报告汇编(含 OFC 2026)

¥1,900

上/下两册,收录 OFC 2026 一线报告
添加微信 WaytoICT 订购

广告

📢 广告位招商:面向全球光通信客户 侧边栏广告位 Email:Dongfei.li@shannoninstitute.cn

最新文档

  • 互连拐点:11 页解析机架内到多机架 Scale-Up 的 XPO/CPX/OCI 蓝图(OCP 2026 全球峰会)
  • AI 时代的相干光技术:17 页解析 Scale-Across、液冷 XPO 与全谱转发器(OCP 2026 全球峰会)
  • XPO 高密度光互连的系统级评估:20 页解析 212G SerDes 平台与 FRO/LRO/LPO 实测(OCP 2026 全球峰会)
  • CPO 与 OCI 标准及未来技术:17 页 Broadcom 精简版演讲提纲(OCP 2026 全球峰会)
  • VCSEL 高密度互连:7 页解析 50G NRZ「慢而宽」阵列与光 PCIe 演示(OCP 2026 全球峰会)

最新评论

暂无评论,欢迎登录后发表第一条评论。

最近访客

👥 今日访客 -
加载中…
© 2026 WaytoICT | 蜀ICP备2020035321号-2 | 隐私政策 | 免责声明
Wechat Pay
Alipay
请使用 支付宝 或 微信 扫码支付